Moog Minitaur Istruzioni per gli Interventi Scaricare il pdf (Pagina 17)

PRESETS

Your Minitaur comes loaded with 94 presets in its internal memory. Up to 128 presets can be saved and loaded using the free Minitaur Editor, or via any

sysex utility. Register your Minitaur at Moogmusic.com/register to get the free plugin and standalone editor.

Minitaur also supports MIDI Program Change messages to change presets. There must be a valid preset saved in the location specified by the Program

Change message in order to change to that preset; otherwise the Program Change message will be ignored.

PRESET SHIFT PANEL FUNCTIONS

NEXT PRESET: Press and hold GLIDE and then press OSCILLATOR 1 WAVE switch.

PREVIOUS PRESET: Press and hold GLIDE and then press OSCILLATOR 2 WAVE switch.

SAVE CURRENT PRESET: Press and hold GLIDE and then press & hold RELEASE switch; hold both for 1 second. Settings will be saved in the

currently-active preset location.

SAVE TO A NEW LOCATION: Press GLIDE + RELEASE switches; let go. You’ll see GLIDE and RELEASE LEDs flashing on and off. You can change

presets in the normal way (hold GLIDE button, press OSCILLATOR 1 or 2 buttons to change preset); when you find a preset you want to save over, hold

GLIDE + Press RELEASE to finish saving. Press RELEASE by itself to cancel without saving.

NEW SHIFT PANEL FUNCTIONS

The GLIDE switch on the Minitaur front panel can now act as a “shift” key, in combination with other panel knobs and buttons, in order to control a

number of additional functions directly from the panel.

To access these additional functions, press and hold the GLIDE switch, and while holding down GLIDE, turn a knob or press an additional switch. As soon

as you activate a “shifted” function in this way, the GLIDE On/Off state will toggle back to the original state it was in before you pressed the GLIDE button.

This way, you can use the GLIDE button for shifted functions without actually changing the GLIDE state.

NEW FUNCTION: Press GLIDE + (additional control)

(Parameter adjustment)

VCO2 BEAT FREQUENCY: Press and hold GLIDE + turn VCO 2 FREQ knob

EXT. INPUT LEVEL: Press and hold GLIDE + turn VCO 1 LEVEL knob

TRIGGER MODE: Press and hold GLIDE + turn FILTER EG ATTACK knob

FILTER EG HOLD TIME: Press and hold GLIDE + turn FILTER EG DECAY/RELEASE knob

AMP EG HOLD TIME: Press and hold GLIDE + turn AMP EG DECAY/RELEASE knob. “Hold” is an envelope phase after Attack and before Decay, in which

the envelope remains at its maximum level for a set amount of time.

PANIC/ALL NOTES OFF: Press and hold GLIDE + turn AMP EG SUSTAIN knob TO ZERO.

GATE ALWAYS ON: Press and hold GLIDE, turn AMP EG SUSTAIN knob TO ZERO, THEN TO MAXIMUM. (do “Panic” function to turn off again)

DECAY & RELEASE MODES

To toggle between Mode 1 and Mode 2 press and hold the RELEASE ON/OFF switch for 1 second. The RELEASE switch LED will blink one time to indicate

Mode 1, or two times to indicate Mode 2. (The selected mode is remembered on power-down).

MODE 1: Control of DECAY and RELEASE time is linked. The RELEASE ON/OFF switch enables or disables the Release stage of the envelope (Release

time is zero if RELEASE ON/OFF is OFF).

MODE 2: DECAY and RELEASE are independent. If the RELEASE ON/OFF switch is lit, the DECAY/R E LE ASE knob is editing the Release time. If

RELEASE ON/OFF is dark, then DECAY/RE LE ASE knob is editing Decay time. In Mode 2, the RELEASE ON/OFF switch doesn’t affect the sound, it only

changes the function of the DECAY/RELEASE knobs.

MOOG MINITAUR FIRMWARE v2.1 ADDENDUM

KNOB MODE

This parameter controls the behavior of the Minitaur panel knobs when their physical position does not match the associated parameter value, which often

happens when changing presets. In Snap mode, as soon as the knob is moved, the parameter value jumps to the current knob position. In Pass-Thru mode,

turning the knob will have no effect on the sound until the knob position matches (“passes through”) the parameter value, after which the knob behaves

as normal. In Relative mode, turning the knob adjusts the parameter value proportionally, so that there are no sudden jumps in value.

LOAD PRESET MOD WHEEL VALUE

If On, loads a saved Mod Wheel value on preset load (the Mod Wheel value that was active when the preset was saved). If Off, then the “live” / current

Mod Wheel value persists on changing presets.

WRAP TOP OCTAVE BEHAVIOR

Now if you play a note which is above C5, the Minitaur will play the equivalent pitch (C, D, E etc.) in its top octave, instead of always playing the highest C

for all notes above C5.

1 2 ... 12 13 14 15 16 17 18 19

Commenti su questo manuale

Nessun commento

Moog Minitaur Istruzioni per gli Interventi Pagina 17

Commenti su questo manuale

Prodotti e manuali riguardandi Sintetizzatore Moog Minitaur